1955 Speedometer erratic moment

[ICON 56]

Don't forget the lube the Distributor, also lube the tach gear too !

This page contains affiliate links for which I may be compensated. As an eBay Partner, and Amazon Associate I may be compensated if you make a purchase at no cost to you.

 

[william]

The speedometer has two main parts, the speedometer head and the speedometer drive cable. When the speedometer fails to indicate speed or mileage, the cable may be broken. Most cables break due to a lack of lubrication or a bend or kink in the housing. The cable also might break when the speedometer head mechanism binds. A jumpy pointer, along with a scraping noise, is often caused by a dry or kinked speedometer cable. The kinked cable rubs on the housing and winds up slowing down the pointer. The cable then unwinds, and the pointer jumps.

To lubricate the cable and check for kinks, the cable will have to be removed from the housing. It is not necessary to remove the housing from the vehicle. From under the dash, disconnect the housing by its fluted nut from the back side of the speedometer head. Prior to removing the cable from the housing, cover the carpet and upholstery, as the common lubricant is graphite which will really make a mess to whatever it touches. Using long nose pliers, pull on the cable while supporting the housing. The cable should come out fairly easily, unless there is a crimp somewhere in the housing, which could be the cause of the problem by itself.

With the cable fully withdrawn and out of the car, inspect the outer surface of the core for flat and shiny areas. These indicate wear areas and you can use their position to approximate the area of the housing that may have an excessive bend or kink. To check for kinks, lay the cable on a flat surface and twist one end with your fingers. If it turns over smoothly, the cable is not kinked. But, if part of the cable flops over as it’s twisted, the cable is kinked and should be replaced.

Before reinstalling the cable back into the housing wipe it down with a clean absorbent cloth and re-lubricate it with a graphite bearing lubricant. Then feed and twist the cable back into the housing. The last 3/8” to 1/4” will require twisting and pushing to engage the square drive at the far end of the cable.

Before re-connecting the cable housing to the back of the speedometer head, put a few drops of lubricant on the wick through the hole in the speedometer head. I had a hard time doing this so I removed the speedometer head from the dash. The speedometer can be removed from the back of the head on a 1957 model, so you do not have to remove the entire head.

doug7740
1955 Thunderbird Blue

Thank you for stating that one has to push and turn the last 3/8 inch the cable to fit into the transmission gear. I believe that oil with graphite will distribute itself better than just grease which will get hard in a few years. William.

 

[kenny1298]

How does one get any lube into this speedo? Thanks

 

[aub]

I recently bought my 57 bird, speedo was not working at all, for what ever reason I removed basil and found the needle was stuck, the person I bought it from said it worked kinda then stop, I dropped 3&1 oil carefully down the backside open shaft carefully moved needle back and forth kept dropping oil and freed it up. Works fine now!
Just something to check if cable is found good.

 

[Rod Bender]

What is the problem with my speedometer? It will move back and forth when driving around 30 to 50 MPH and then is steady on a speed when it is going 60-70 MPH. There is no noise coming from it (as I would expect if needed grease) just this steady movement at lower speeds?

MODERATOR NOTE: Use Cable Lubricant! Click here to buy.
View attachment 26993

There is an angled fitting that you can purchase that will take the bind out of the cable that will give you a straighter shot on the line.

 

[Hwoodlive]

Another of the many suggesting you lube your speedo cable, but here's a twist (pun intended): I recently purchased a replacement cable for my '59 Galaxie and it was a perfect fit EXCEPT that it was several inches too long. You'd think that wouldn't be a big deal, but it was just enough excess that I couldn't get a smooth arc from top to bottom; the resulting small kink caused the speedo to jump at lower speeds.